ArduShop.ro

ArduShop.ro
cod Z4A413ZN reducere 5%, pentru vizitatorii paginilor mele !

luni, 1 iulie 2013

Afisaje LED cu 7 segmente si.. Arduino (II)

   Fata de prima parte prima parte unde doar am facut o prezentare scurta a unui numarator cu indicarea valorilor pe un afisaj cu 4 cifre de 7 segmente tip LED multiplexate, acum fac si altceva mai complex...
   Pentru inceput o sa modific modul de conectare al afisajului, deoarece 2 dintre intrarile analogice (A0 si A1) erau conectate ca iesiri digitale. Pe langa faptul ca-mi reduce numarul de intrari analogice, si modul de legare este incurcat...
   Fara a folosi o librarie dedicata pentru acest afisaj, am modificat sketch-ul anterior (din articol mentionat inainte), in sensul ca am definit simbolul pentru grad Celsius si 2 litere (C si H). Am definit o subrutina diferita pentru umiditate, fata de cea pentru temperatura si am folosit partea de program de la senzorul de temeperatura si uniditate DHT11, cum e in ultimul sketch din articolul Ministatie meteo cu senzorul DHT11 si.. Arduino, pinul de date fiind tot A2.
   Un film, in care se prezinta modul de afisare, se numeste temperature & humidity on 7 segment LED display
Sketch-ul meu este:
/*
 6-13-2011
 Spark Fun Electronics 2011
 Nathan Seidle

 This code is public domain but you buy me a beer if you use this and we meet 
 someday (Beerware license).

 4 digit 7 segment display:
 Datasheet: 

 This is an example of how to drive a 7 segment LED display from an ATmega
 without the use of current limiting resistors. This technique is very common 
 but requires some knowledge of electronics - you do run the risk of dumping 
 too much current through the segments and burning out parts of the display. 
 If you use the stock code you should be ok, but be careful editing the 
 brightness values.

 This code should work with all colors (red, blue, yellow, green) but the 
 brightness will vary from one color to the next because the forward voltage 
 drop of each color is different. This code was written and calibrated for the 
 red color.

 This code will work with most Arduinos but you may want to re-route some of 
 the pins.

 7 segments
 4 digits
 1 colon
 =
 12 pins required for full control 

 */
// modified connexion by niq_ro from http://nicuflorica.blogspot.com
// for my Luckylight KW4-563ASA

int digit1 = 11; //PWM Display pin 12 (digit1 is common anonds A1 from right side)
int digit2 = 10; //PWM Display pin 9 (digit2 is  common A2)
int digit3 = 9; //PWM Display pin 8 (digit3 is common anods A3)
int digit4 = 6; //PWM Display pin 6 (digit4 is common anods, from left side)

//Pin mapping from Arduino to the ATmega DIP28 if you need it
int segA = 2; //Display pin 11
int segB = 3; //Display pin 7
int segC = 4; //Display pin 4
int segD = 5; //Display pin 2
int segE = 12; //Display pin 1
int segF = 7; //Display pin 10
int segG = 8; //Display pin 5

#include "DHT.h"
#define DHTPIN A2     // what pin we're connected to
#define DHTTYPE DHT11   // DHT 11 
DHT dht(DHTPIN, DHTTYPE);

void setup() {

 dht.begin();

  pinMode(segA, OUTPUT);
  pinMode(segB, OUTPUT);
  pinMode(segC, OUTPUT);
  pinMode(segD, OUTPUT);
  pinMode(segE, OUTPUT);
  pinMode(segF, OUTPUT);
  pinMode(segG, OUTPUT);

  pinMode(digit1, OUTPUT);
  pinMode(digit2, OUTPUT);
  pinMode(digit3, OUTPUT);
  pinMode(digit4, OUTPUT);
  
  pinMode(13, OUTPUT);
}

void loop() {
   
   int h = dht.readHumidity();
   int t = dht.readTemperature();

   for(int i = 1000 ; i >0  ; i--) {
     displayNumber(t); // this is number to diplay
   }
   
   for(int i = 1000 ; i >0  ; i--) {
     displayNumber1(h); // this is number to diplay
   }
   
//   displayNumber(12); // this is number to diplay
}


//Given a number, we display 10:22
//After running through the 4 numbers, the display is left turned off

//Display brightness
//Each digit is on for a certain amount of microseconds
//Then it is off until we have reached a total of 20ms for the function call
//Let's assume each digit is on for 1000us
//Each digit is on for 1ms, there are 4 digits, so the display is off for 16ms.
//That's a ratio of 1ms to 16ms or 6.25% on time (PWM).
//Let's define a variable called brightness that varies from:
//5000 blindingly bright (15.7mA current draw per digit)
//2000 shockingly bright (11.4mA current draw per digit)
//1000 pretty bright (5.9mA)
//500 normal (3mA)
//200 dim but readable (1.4mA)
//50 dim but readable (0.56mA)
//5 dim but readable (0.31mA)
//1 dim but readable in dark (0.28mA)

void displayNumber(int toDisplay) {
#define DISPLAY_BRIGHTNESS  500

#define DIGIT_ON  HIGH
#define DIGIT_OFF  LOW


  for(int digit = 4 ; digit > 0 ; digit--) {

    //Turn on a digit for a short amount of time
    switch(digit) {
    case 1:
      digitalWrite(digit1, DIGIT_ON);
      lightNumber(toDisplay % 10);
      toDisplay /= 10;
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
   case 2:
      digitalWrite(digit2, DIGIT_ON);
      lightNumber(toDisplay % 10);
      toDisplay /= 10;
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
    case 3:
      digitalWrite(digit3, DIGIT_ON);
      lightNumber(11); // display degree symbol
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
    case 4:
      digitalWrite(digit4, DIGIT_ON);
      lightNumber(12); // display C letter
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
    }
     //Turn off all segments
    lightNumber(10); 

    //Turn off all digits
    digitalWrite(digit1, DIGIT_OFF);
    digitalWrite(digit2, DIGIT_OFF);
    digitalWrite(digit3, DIGIT_OFF);
    digitalWrite(digit4, DIGIT_OFF);
}

void displayNumber1(int toDisplay) {
#define DISPLAY_BRIGHTNESS  500

#define DIGIT_ON  HIGH
#define DIGIT_OFF  LOW


  for(int digit = 4 ; digit > 0 ; digit--) {

    //Turn on a digit for a short amount of time
    switch(digit) {
    case 1:
      digitalWrite(digit1, DIGIT_ON);
      lightNumber(toDisplay % 10);
      toDisplay /= 10;
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
   case 2:
      digitalWrite(digit2, DIGIT_ON);
      lightNumber(toDisplay % 10);
      toDisplay /= 10;
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
    case 3:
      digitalWrite(digit3, DIGIT_ON);
      lightNumber(10); // display degree symbol
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
    case 4:
      digitalWrite(digit4, DIGIT_ON);
      lightNumber(13); // display C letter
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
    }
     //Turn off all segments
    lightNumber(10); 

    //Turn off all digits
    digitalWrite(digit1, DIGIT_OFF);
    digitalWrite(digit2, DIGIT_OFF);
    digitalWrite(digit3, DIGIT_OFF);
    digitalWrite(digit4, DIGIT_OFF);
}



//Given a number, turns on those segments
//If number == 10, then turn off number
void lightNumber(int numberToDisplay) {

#define SEGMENT_ON  LOW
#define SEGMENT_OFF HIGH

  switch (numberToDisplay){

  case 0:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_ON);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_OFF);
    break;

  case 1:
    digitalWrite(segA, SEGMENT_OFF);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_OFF);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_OFF);
    digitalWrite(segG, SEGMENT_OFF);
    break;

  case 2:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_OFF);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_ON);
    digitalWrite(segF, SEGMENT_OFF);
    digitalWrite(segG, SEGMENT_ON);
    break;

  case 3:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_OFF);
    digitalWrite(segG, SEGMENT_ON);
    break;

  case 4:
    digitalWrite(segA, SEGMENT_OFF);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_OFF);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_ON);
    break;

  case 5:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_OFF);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_ON);
    break;

  case 6:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_OFF);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_ON);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_ON);
    break;

  case 7:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_OFF);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_OFF);
    digitalWrite(segG, SEGMENT_OFF);
    break;

  case 8:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_ON);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_ON);
    break;

  case 9:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_ON);
    break;

  // all segment are ON
  case 10:
    digitalWrite(segA, SEGMENT_OFF);
    digitalWrite(segB, SEGMENT_OFF);
    digitalWrite(segC, SEGMENT_OFF);
    digitalWrite(segD, SEGMENT_OFF);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_OFF);
    digitalWrite(segG, SEGMENT_OFF);
    break;
  
  // degree symbol made by niq_ro
  case 11:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_OFF);
    digitalWrite(segD, SEGMENT_OFF);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_ON);
    break;

  // C letter made by niq_ro
  case 12:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_OFF);
    digitalWrite(segC, SEGMENT_OFF);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_ON);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_OFF);
    break;
  
  // H letter made by niq_ro
  case 13:
    digitalWrite(segA, SEGMENT_OFF);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_OFF);
    digitalWrite(segE, SEGMENT_ON);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_ON);
    break;
  }
}
   Un filmulet, la o calitate mai buna, se numeste temperature & humidity on 7 segment LED display (II)
02.iul.2013
   M-am gandit ca ar fi mai spectaculos si mai util ca pe afisaj sa am indicata si ora, asa ca am conectat modulul de timp real cu DS1307 si am legat si terminalul de la afisajul multiplexat pentru punctul zecimal, modificand si sketch-ul.
   Am facut un filmulet, care se numeste hour, temperature & humidity on 7-segment LED display with Arduino:

/*
 6-13-2011
 Spark Fun Electronics 2011
 Nathan Seidle

 This code is public domain but you buy me a beer if you use this and we meet 
 someday (Beerware license).

 4 digit 7 segment display:
 Datasheet: 

 This is an example of how to drive a 7 segment LED display from an ATmega
 without the use of current limiting resistors. This technique is very common 
 but requires some knowledge of electronics - you do run the risk of dumping 
 too much current through the segments and burning out parts of the display. 
 If you use the stock code you should be ok, but be careful editing the 
 brightness values.

 This code should work with all colors (red, blue, yellow, green) but the 
 brightness will vary from one color to the next because the forward voltage 
 drop of each color is different. This code was written and calibrated for the 
 red color.

 This code will work with most Arduinos but you may want to re-route some of 
 the pins.

 7 segments
 4 digits
 1 colon
 =
 12 pins required for full control 

 */
// modified connexion by niq_ro from http://nicuflorica.blogspot.com
// for my Luckylight KW4-563ASA

int digit1 = 11; //PWM Display pin 12 (digit1 is common anonds A1 from right side)
int digit2 = 10; //PWM Display pin 9 (digit2 is  common A2)
int digit3 = 9; //PWM Display pin 8 (digit3 is common anods A3)
int digit4 = 6; //PWM Display pin 6 (digit4 is common anods, from left side)

//Pin mapping from Arduino to the ATmega DIP28 if you need it
int segA = 2; //Display pin 11
int segB = 3; //Display pin 7
int segC = 4; //Display pin 4
int segD = 5; //Display pin 2
int segE = 12; //Display pin 1
int segF = 7; //Display pin 10
int segG = 8; //Display pin 5
int segDP = 13; // Display pin 3

#include "DHT.h"
#define DHTPIN A2     // what pin we're connected to
#define DHTTYPE DHT11   // DHT 11 
DHT dht(DHTPIN, DHTTYPE);

#include <Wire.h>
#include "RTClib.h"
RTC_DS1307 RTC;

// Date and time functions using a DS1307 RTC connected via I2C and Wire lib


void setup() {

  Wire.begin();
  RTC.begin();
// RTC.adjust(DateTime(__DATE__, __TIME__));
// if you need set clock... just remove // from line above this

// part code for flashing LED
Wire.beginTransmission(0x68);
Wire.write(0x07); // move pointer to SQW address
// Wire.write(0x00); // turns the SQW pin off
 Wire.write(0x10); // sends 0x10 (hex) 00010000 (binary) to control register - turns on square wave at 1Hz
// Wire.write(0x13); // sends 0x13 (hex) 00010011 (binary) 32kHz

Wire.endTransmission();

  if (! RTC.isrunning()) {
    Serial.println("RTC is NOT running!");
    // following line sets the RTC to the date & time this sketch was compiled
    RTC.adjust(DateTime(__DATE__, __TIME__));
  }
  
  
 dht.begin();

  pinMode(segA, OUTPUT);
  pinMode(segB, OUTPUT);
  pinMode(segC, OUTPUT);
  pinMode(segD, OUTPUT);
  pinMode(segE, OUTPUT);
  pinMode(segF, OUTPUT);
  pinMode(segG, OUTPUT);
  pinMode(segDP, OUTPUT);

  pinMode(digit1, OUTPUT);
  pinMode(digit2, OUTPUT);
  pinMode(digit3, OUTPUT);
  pinMode(digit4, OUTPUT);
  
//  pinMode(13, OUTPUT);

 Serial.begin(9600);
 Serial.println("test for niq_ro");
}

void loop() {
digitalWrite(segDP, HIGH);
  DateTime now = RTC.now();
   int timp = now.hour()*100+now.minute();
//   int timp = (now.minute(), DEC);
//   displayNumber(12); // this is number to diplay
//   int timp = 1234;
  Serial.print(now.hour(), DEC);
  Serial.print(":");
  Serial.print(now.minute(), DEC);
  Serial.print(" -> ");
  Serial.print(timp);
  Serial.println(" !");
  
   int h = dht.readHumidity();
   int t = dht.readTemperature();

   for(int i = 1000 ; i >0  ; i--) {
     displayNumber(t); // this is number to diplay
   }
   
   for(int i = 1000 ; i >0  ; i--) {
     displayNumber1(h); // this is number to diplay
   }
   
   for(int i = 1000 ; i >0  ; i--) {
     displayNumber0(timp); // this is number to diplay
   }
  
}


//Given a number, we display 10:22
//After running through the 4 numbers, the display is left turned off

//Display brightness
//Each digit is on for a certain amount of microseconds
//Then it is off until we have reached a total of 20ms for the function call
//Let's assume each digit is on for 1000us
//Each digit is on for 1ms, there are 4 digits, so the display is off for 16ms.
//That's a ratio of 1ms to 16ms or 6.25% on time (PWM).
//Let's define a variable called brightness that varies from:
//5000 blindingly bright (15.7mA current draw per digit)
//2000 shockingly bright (11.4mA current draw per digit)
//1000 pretty bright (5.9mA)
//500 normal (3mA)
//200 dim but readable (1.4mA)
//50 dim but readable (0.56mA)
//5 dim but readable (0.31mA)
//1 dim but readable in dark (0.28mA)

void displayNumber(int toDisplay) {
#define DISPLAY_BRIGHTNESS  500

#define DIGIT_ON  HIGH
#define DIGIT_OFF  LOW


  for(int digit = 4 ; digit > 0 ; digit--) {

    //Turn on a digit for a short amount of time
    switch(digit) {
    case 1:
      digitalWrite(digit1, DIGIT_ON);
      lightNumber(toDisplay % 10);
      toDisplay /= 10;
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
   case 2:
      digitalWrite(digit2, DIGIT_ON);
      lightNumber(toDisplay % 10);
      toDisplay /= 10;
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
    case 3:
      digitalWrite(digit3, DIGIT_ON);
      lightNumber(11); // display degree symbol
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
    case 4:
      digitalWrite(digit4, DIGIT_ON);
      lightNumber(12); // display C letter
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
    }
     //Turn off all segments
    lightNumber(10); 

    //Turn off all digits
    digitalWrite(digit1, DIGIT_OFF);
    digitalWrite(digit2, DIGIT_OFF);
    digitalWrite(digit3, DIGIT_OFF);
    digitalWrite(digit4, DIGIT_OFF);
}

void displayNumber1(int toDisplay) {
#define DISPLAY_BRIGHTNESS  500

#define DIGIT_ON  HIGH
#define DIGIT_OFF  LOW


  for(int digit = 4 ; digit > 0 ; digit--) {

    //Turn on a digit for a short amount of time
    switch(digit) {
    case 1:
      digitalWrite(digit1, DIGIT_ON);
      lightNumber(toDisplay % 10);
      toDisplay /= 10;
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
   case 2:
      digitalWrite(digit2, DIGIT_ON);
      lightNumber(toDisplay % 10);
      toDisplay /= 10;
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
    case 3:
      digitalWrite(digit3, DIGIT_ON);
      lightNumber(10); // display degree symbol
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
    case 4:
      digitalWrite(digit4, DIGIT_ON);
      lightNumber(13); // display C letter
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
    }
     //Turn off all segments
    lightNumber(10); 

    //Turn off all digits
    digitalWrite(digit1, DIGIT_OFF);
    digitalWrite(digit2, DIGIT_OFF);
    digitalWrite(digit3, DIGIT_OFF);
    digitalWrite(digit4, DIGIT_OFF);
}

void displayNumber0(int toDisplay) {
#define DISPLAY_BRIGHTNESS  500

#define DIGIT_ON  HIGH
#define DIGIT_OFF  LOW

  for(int digit = 4 ; digit > 0 ; digit--) {

    //Turn on a digit for a short amount of time
    switch(digit) {
    case 1:
      digitalWrite(digit1, DIGIT_ON);
      digitalWrite(segDP, HIGH);
      break;
   case 2:
      digitalWrite(digit2, DIGIT_ON);
      digitalWrite(segDP, LOW);
      break;
    case 3:
      digitalWrite(digit3, DIGIT_ON);
      digitalWrite(segDP, HIGH);
      break;
    case 4:
      digitalWrite(digit4, DIGIT_ON);
      digitalWrite(segDP, HIGH);
      break;
    }
    lightNumber(toDisplay % 10);
    toDisplay /= 10;
    delayMicroseconds(DISPLAY_BRIGHTNESS); 

     //Turn off all segments
    lightNumber(10); 

    //Turn off all digits
    digitalWrite(digit1, DIGIT_OFF);
    digitalWrite(digit2, DIGIT_OFF);
    digitalWrite(digit3, DIGIT_OFF);
    digitalWrite(digit4, DIGIT_OFF);
}


//Given a number, turns on those segments
//If number == 10, then turn off number
void lightNumber(int numberToDisplay) {

#define SEGMENT_ON  LOW
#define SEGMENT_OFF HIGH

  switch (numberToDisplay){

  case 0:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_ON);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_OFF);
    break;

  case 1:
    digitalWrite(segA, SEGMENT_OFF);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_OFF);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_OFF);
    digitalWrite(segG, SEGMENT_OFF);
    break;

  case 2:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_OFF);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_ON);
    digitalWrite(segF, SEGMENT_OFF);
    digitalWrite(segG, SEGMENT_ON);
    break;

  case 3:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_OFF);
    digitalWrite(segG, SEGMENT_ON);
    break;

  case 4:
    digitalWrite(segA, SEGMENT_OFF);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_OFF);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_ON);
    break;

  case 5:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_OFF);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_ON);
    break;

  case 6:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_OFF);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_ON);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_ON);
    break;

  case 7:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_OFF);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_OFF);
    digitalWrite(segG, SEGMENT_OFF);
    break;

  case 8:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_ON);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_ON);
    break;

  case 9:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_ON);
    break;

  // all segment are ON
  case 10:
    digitalWrite(segA, SEGMENT_OFF);
    digitalWrite(segB, SEGMENT_OFF);
    digitalWrite(segC, SEGMENT_OFF);
    digitalWrite(segD, SEGMENT_OFF);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_OFF);
    digitalWrite(segG, SEGMENT_OFF);
    break;
  
  // degree symbol made by niq_ro
  case 11:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_OFF);
    digitalWrite(segD, SEGMENT_OFF);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_ON);
    break;

  // C letter made by niq_ro
  case 12:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_OFF);
    digitalWrite(segC, SEGMENT_OFF);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_ON);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_OFF);
    break;
  
  // H letter made by niq_ro
  case 13:
    digitalWrite(segA, SEGMENT_OFF);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_OFF);
    digitalWrite(segE, SEGMENT_ON);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_ON);
    break;
  }
}
   Deoarece ma deranja acel zero din fata orei, am modificat sketch-ul sa am afisata ora fara acel zero...
/*
 6-13-2011
 Spark Fun Electronics 2011
 Nathan Seidle

 This code is public domain but you buy me a beer if you use this and we meet 
 someday (Beerware license).

 4 digit 7 segment display:
 Datasheet: 

 This is an example of how to drive a 7 segment LED display from an ATmega
 without the use of current limiting resistors. This technique is very common 
 but requires some knowledge of electronics - you do run the risk of dumping 
 too much current through the segments and burning out parts of the display. 
 If you use the stock code you should be ok, but be careful editing the 
 brightness values.

 This code should work with all colors (red, blue, yellow, green) but the 
 brightness will vary from one color to the next because the forward voltage 
 drop of each color is different. This code was written and calibrated for the 
 red color.

 This code will work with most Arduinos but you may want to re-route some of 
 the pins.

 7 segments
 4 digits
 1 colon
 =
 12 pins required for full control 

 */
// modified connexion by niq_ro from http://nicuflorica.blogspot.com
// for my Luckylight KW4-563ASA

int digit1 = 11; //PWM Display pin 12 (digit1 is common anonds A1 from right side)
int digit2 = 10; //PWM Display pin 9 (digit2 is  common A2)
int digit3 = 9; //PWM Display pin 8 (digit3 is common anods A3)
int digit4 = 6; //PWM Display pin 6 (digit4 is common anods, from left side)

//Pin mapping from Arduino to the ATmega DIP28 if you need it
int segA = 2; //Display pin 11
int segB = 3; //Display pin 7
int segC = 4; //Display pin 4
int segD = 5; //Display pin 2
int segE = 12; //Display pin 1
int segF = 7; //Display pin 10
int segG = 8; //Display pin 5
int segDP = 13; // Display pin 3

#include "DHT.h"
#define DHTPIN A2     // what pin we're connected to
#define DHTTYPE DHT11   // DHT 11 
DHT dht(DHTPIN, DHTTYPE);

#include <Wire.h>
#include "RTClib.h"
RTC_DS1307 RTC;

// Date and time functions using a DS1307 RTC connected via I2C and Wire lib


void setup() {

  Wire.begin();
  RTC.begin();
// RTC.adjust(DateTime(__DATE__, __TIME__));
// if you need set clock... just remove // from line above this

// part code for flashing LED
Wire.beginTransmission(0x68);
Wire.write(0x07); // move pointer to SQW address
// Wire.write(0x00); // turns the SQW pin off
 Wire.write(0x10); // sends 0x10 (hex) 00010000 (binary) to control register - turns on square wave at 1Hz
// Wire.write(0x13); // sends 0x13 (hex) 00010011 (binary) 32kHz

Wire.endTransmission();

  if (! RTC.isrunning()) {
    Serial.println("RTC is NOT running!");
    // following line sets the RTC to the date & time this sketch was compiled
    RTC.adjust(DateTime(__DATE__, __TIME__));
  }
  
  
 dht.begin();

  pinMode(segA, OUTPUT);
  pinMode(segB, OUTPUT);
  pinMode(segC, OUTPUT);
  pinMode(segD, OUTPUT);
  pinMode(segE, OUTPUT);
  pinMode(segF, OUTPUT);
  pinMode(segG, OUTPUT);
  pinMode(segDP, OUTPUT);

  pinMode(digit1, OUTPUT);
  pinMode(digit2, OUTPUT);
  pinMode(digit3, OUTPUT);
  pinMode(digit4, OUTPUT);
  
//  pinMode(13, OUTPUT);

 Serial.begin(9600);
 Serial.println("test for niq_ro");
}

void loop() {
digitalWrite(segDP, HIGH);
  DateTime now = RTC.now();
   int timp = now.hour()*100+now.minute();
//   int timp = (now.minute(), DEC);
//   displayNumber(12); // this is number to diplay
//   int timp = 1234;
  Serial.print(now.hour(), DEC);
  Serial.print(":");
  Serial.print(now.minute(), DEC);
  Serial.print(" -> ");
  Serial.print(timp);
  Serial.println(" !");
  
   int h = dht.readHumidity();
   int t = dht.readTemperature();

   for(int i = 1000 ; i >0  ; i--) {
     displayNumber(t); // this is number to diplay
   }
   
   for(int i = 1000 ; i >0  ; i--) {
     displayNumber1(h); // this is number to diplay
   }
   
   for(int i = 1000 ; i >0  ; i--) {
     if (timp > 1000) displayNumber01(timp); 
     else displayNumber02(timp); 
   } 
  
}


//Given a number, we display 10:22
//After running through the 4 numbers, the display is left turned off

//Display brightness
//Each digit is on for a certain amount of microseconds
//Then it is off until we have reached a total of 20ms for the function call
//Let's assume each digit is on for 1000us
//Each digit is on for 1ms, there are 4 digits, so the display is off for 16ms.
//That's a ratio of 1ms to 16ms or 6.25% on time (PWM).
//Let's define a variable called brightness that varies from:
//5000 blindingly bright (15.7mA current draw per digit)
//2000 shockingly bright (11.4mA current draw per digit)
//1000 pretty bright (5.9mA)
//500 normal (3mA)
//200 dim but readable (1.4mA)
//50 dim but readable (0.56mA)
//5 dim but readable (0.31mA)
//1 dim but readable in dark (0.28mA)

void displayNumber(int toDisplay) {
#define DISPLAY_BRIGHTNESS  500

#define DIGIT_ON  HIGH
#define DIGIT_OFF  LOW


  for(int digit = 4 ; digit > 0 ; digit--) {

    //Turn on a digit for a short amount of time
    switch(digit) {
    case 1:
      digitalWrite(digit1, DIGIT_ON);
      lightNumber(toDisplay % 10);
      toDisplay /= 10;
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
   case 2:
      digitalWrite(digit2, DIGIT_ON);
      lightNumber(toDisplay % 10);
      toDisplay /= 10;
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
    case 3:
      digitalWrite(digit3, DIGIT_ON);
      lightNumber(11); // display degree symbol
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
    case 4:
      digitalWrite(digit4, DIGIT_ON);
      lightNumber(12); // display C letter
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
    }
     //Turn off all segments
    lightNumber(10); 

    //Turn off all digits
    digitalWrite(digit1, DIGIT_OFF);
    digitalWrite(digit2, DIGIT_OFF);
    digitalWrite(digit3, DIGIT_OFF);
    digitalWrite(digit4, DIGIT_OFF);
}

void displayNumber1(int toDisplay) {
#define DISPLAY_BRIGHTNESS  500

#define DIGIT_ON  HIGH
#define DIGIT_OFF  LOW


  for(int digit = 4 ; digit > 0 ; digit--) {

    //Turn on a digit for a short amount of time
    switch(digit) {
    case 1:
      digitalWrite(digit1, DIGIT_ON);
      lightNumber(toDisplay % 10);
      toDisplay /= 10;
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
   case 2:
      digitalWrite(digit2, DIGIT_ON);
      lightNumber(toDisplay % 10);
      toDisplay /= 10;
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
    case 3:
      digitalWrite(digit3, DIGIT_ON);
      lightNumber(10); // display degree symbol
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
    case 4:
      digitalWrite(digit4, DIGIT_ON);
      lightNumber(13); // display C letter
      delayMicroseconds(DISPLAY_BRIGHTNESS); 
      break;
    }
     //Turn off all segments
    lightNumber(10); 

    //Turn off all digits
    digitalWrite(digit1, DIGIT_OFF);
    digitalWrite(digit2, DIGIT_OFF);
    digitalWrite(digit3, DIGIT_OFF);
    digitalWrite(digit4, DIGIT_OFF);
}

void displayNumber01(int toDisplay) {
#define DISPLAY_BRIGHTNESS  500

#define DIGIT_ON  HIGH
#define DIGIT_OFF  LOW

  for(int digit = 4 ; digit > 0 ; digit--) {

    //Turn on a digit for a short amount of time
    switch(digit) {
    case 1:
     digitalWrite(digit1, DIGIT_ON);
     digitalWrite(segDP, HIGH);
      break;
   case 2:
      digitalWrite(digit2, DIGIT_ON);
      digitalWrite(segDP, LOW);
      break;
    case 3:
      digitalWrite(digit3, DIGIT_ON);
      digitalWrite(segDP, HIGH);
      break;
    case 4:
      digitalWrite(digit4, DIGIT_ON);
      digitalWrite(segDP, HIGH);
      break;
    }
    lightNumber(toDisplay % 10);
    toDisplay /= 10;
    delayMicroseconds(DISPLAY_BRIGHTNESS); 

     //Turn off all segments
    lightNumber(10); 

    //Turn off all digits
    digitalWrite(digit1, DIGIT_OFF);
    digitalWrite(digit2, DIGIT_OFF);
    digitalWrite(digit3, DIGIT_OFF);
    digitalWrite(digit4, DIGIT_OFF);
}

void displayNumber02(int toDisplay) {
#define DISPLAY_BRIGHTNESS  500

#define DIGIT_ON  HIGH
#define DIGIT_OFF  LOW

  for(int digit = 4 ; digit > 0 ; digit--) {

    //Turn on a digit for a short amount of time
    switch(digit) {
    case 1:
     lightNumber(10); 
     digitalWrite(segDP, HIGH);
     break;
   case 2:
      digitalWrite(digit2, DIGIT_ON);
      digitalWrite(segDP, LOW);
      break;
    case 3:
      digitalWrite(digit3, DIGIT_ON);
      digitalWrite(segDP, HIGH);
      break;
    case 4:
      digitalWrite(digit4, DIGIT_ON);
      digitalWrite(segDP, HIGH);
      break;
    }
    lightNumber(toDisplay % 10);
    toDisplay /= 10;
    delayMicroseconds(DISPLAY_BRIGHTNESS); 

     //Turn off all segments
    lightNumber(10); 

    //Turn off all digits
    digitalWrite(digit1, DIGIT_OFF);
    digitalWrite(digit2, DIGIT_OFF);
    digitalWrite(digit3, DIGIT_OFF);
    digitalWrite(digit4, DIGIT_OFF);
}


//Given a number, turns on those segments
//If number == 10, then turn off number
void lightNumber(int numberToDisplay) {

#define SEGMENT_ON  LOW
#define SEGMENT_OFF HIGH

  switch (numberToDisplay){

  case 0:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_ON);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_OFF);
    break;

  case 1:
    digitalWrite(segA, SEGMENT_OFF);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_OFF);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_OFF);
    digitalWrite(segG, SEGMENT_OFF);
    break;

  case 2:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_OFF);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_ON);
    digitalWrite(segF, SEGMENT_OFF);
    digitalWrite(segG, SEGMENT_ON);
    break;

  case 3:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_OFF);
    digitalWrite(segG, SEGMENT_ON);
    break;

  case 4:
    digitalWrite(segA, SEGMENT_OFF);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_OFF);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_ON);
    break;

  case 5:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_OFF);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_ON);
    break;

  case 6:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_OFF);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_ON);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_ON);
    break;

  case 7:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_OFF);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_OFF);
    digitalWrite(segG, SEGMENT_OFF);
    break;

  case 8:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_ON);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_ON);
    break;

  case 9:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_ON);
    break;

  // all segment are ON
  case 10:
    digitalWrite(segA, SEGMENT_OFF);
    digitalWrite(segB, SEGMENT_OFF);
    digitalWrite(segC, SEGMENT_OFF);
    digitalWrite(segD, SEGMENT_OFF);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_OFF);
    digitalWrite(segG, SEGMENT_OFF);
    break;
  
  // degree symbol made by niq_ro
  case 11:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_OFF);
    digitalWrite(segD, SEGMENT_OFF);
    digitalWrite(segE, SEGMENT_OFF);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_ON);
    break;

  // C letter made by niq_ro
  case 12:
    digitalWrite(segA, SEGMENT_ON);
    digitalWrite(segB, SEGMENT_OFF);
    digitalWrite(segC, SEGMENT_OFF);
    digitalWrite(segD, SEGMENT_ON);
    digitalWrite(segE, SEGMENT_ON);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_OFF);
    break;
  
  // H letter made by niq_ro
  case 13:
    digitalWrite(segA, SEGMENT_OFF);
    digitalWrite(segB, SEGMENT_ON);
    digitalWrite(segC, SEGMENT_ON);
    digitalWrite(segD, SEGMENT_OFF);
    digitalWrite(segE, SEGMENT_ON);
    digitalWrite(segF, SEGMENT_ON);
    digitalWrite(segG, SEGMENT_ON);
    break;
  }
}




20 de comentarii:

  1. imi scrie asa ceva ajutati ma va rog



    sketch_jul03h:60: error: 'DHT' does not name a type

    DHT dht(DHTPIN, DHTTYPE);

    ^

    C:\Users\oscared51\Documents\Arduino\sketch_jul03h\sketch_jul03h.ino: In function 'void setup()':

    sketch_jul03h:64: error: 'dht' was not declared in this scope

    dht.begin();

    ^

    C:\Users\oscared51\Documents\Arduino\sketch_jul03h\sketch_jul03h.ino: In function 'void loop()':

    sketch_jul03h:84: error: 'dht' was not declared in this scope

    int h = dht.readHumidity();

    ^

    exit status 1
    'DHT' does not name a type

    RăspundețiȘtergere
  2. nu ai libraria DHT corecta sau nu o ai deloc...

    RăspundețiȘtergere
  3. Răspunsuri
    1. what time zone? how is ïndian time zone"... this clock indicate just hour and minute...

      Ștergere
  4. When I complie the code and upload it. The time set -5.30 hour from current time

    RăspundețiȘtergere
  5. How to set local hour, where i connect manual adjust button?

    RăspundețiȘtergere
    Răspunsuri
    1. in this article is just "automatic".. find line
      // RTC.adjust(DateTime(__DATE__, __TIME__));
      // if you need set clock... just remove // from line above this

      remove // upload sketch, add // and upload... RTC module give PC hour and minutes

      Ștergere
  6. see other article: https://nicuflorica.blogspot.ro/2013/12/afisaje-led-cu-7-segmente-si-arduino-iv.html

    RăspundețiȘtergere
  7. It's works fine now. If there is also manual adjust button, it's good for everyone. Please remodify it for public.

    RăspundețiȘtergere
  8. Sir, i successfully made it. But one problem... the time is not set in rtc, after power off, it back to complie time.

    RăspundețiȘtergere
  9. Hello, Nicu FLORICA,
    I would like to ask you to explain much more variables of project about thermostat. The program was anywhere here, but I cannot understand everything of it. Please comment more variables, each one if possible, how and for what is it used for....
    I would buy you much more than a beer, because I will try to make a thermoregulator , with alarm clock turning on heater and manual turn off. I mean there will be in later project (after just perfect running thermoregulator itself).
    With respect : Anatoliy

    RăspundețiȘtergere
    Răspunsuri
    1. for thermostat see in english version of my blog: http://arduinotehniq.blogspot.ro/2015/05/arduino-thermostat-on-7-segment-led.html and http://arduinotehniq.blogspot.ro/2015/05/arduino-thermostat-with-2-thresholds-on.html

      Ștergere
  10. Sir please provide code for common cathode display

    RăspundețiȘtergere
    Răspunsuri
    1. change all line
      #define SEGMENT_ON LOW
      #define SEGMENT_OFF HIGH
      with
      #define SEGMENT_ON HIGH
      #define SEGMENT_OFF LOW
      and
      #define DIGIT_ON HIGH
      #define DIGIT_OFF LOW
      with
      #define DIGIT_ON LOW
      #define DIGIT_OFF HIGH

      Ștergere
    2. Thanks, i successfully made it.

      Ștergere
  11. Sir, is it possible to show 00.00 replace 0.00? Like 8.15=08.15, 9.30=09.30

    RăspundețiȘtergere

Senzor de masurare tensiune si curent INA219

   Am achizitionat de curand, de la colaboratorii mei de la  ArduShop.ro , un modul cu senzor INA219, care poate masura tensiuni pana la 26V...